Ergotron StyleView Betriebsanweisung PDF herunterladen (Seite 26)

26/27

888-24-314-G-00 rev. B • 12/14

Medical-Grade

Power Strip

97-466

Fully tested, certified and compliant to:

UL 1363A

Input and Output: 120 V~, 60 Hz, 15 A max

822-104-01

Made in China

yyww

ENGLISH

Maintenance & Safety

Earth Bond Test: To ensure safety grounding between the

power cord ground connection and any accessible metal

parts on the cart, although not mandatory, the following test

is recommended to be performed every two years using a

calibrated medical device safety analyzer. The procedure is as

follows:

1. Disconnect the cart from mains power (unplug cart from the

wall).

2. Remove power from internal power system outlets by

pressing the power button on the Power System Interface.

3. Set up Earth Bond Test per the medical device safety analyzer

instructions.

4. Connect the Cart power cord to the medical device safety

analyzer.

5. Remove cover to access Lift Tension Adjustment point.

6. Attach second medical safety device analyzer probe to Lift

Tension Adjustment point on Cart.

7. Perform Test (25 amps).

8. Ensure Earth Bond is less than or equal to 0.2-ohms.

9. Remove medical device safety analyzer connections to Cart,

replace cover over Lift Tension Adjustment point, return the

Cart to service.

Insulation Resistance Test: To ensure mains power lines are

adequately insulated from earth ground, the following test,

although not mandatory, is recommended to be performed

annually using a calibrated medical device safety analyzer. The

procedure is as follows:

1. Disconnect the cart from mains power (unplug cart from the

wall).

2. Remove power from internal power system outlets by

pressing the power button on the Power System Interface.

3. Set up the Insulation Resistance Test per the medical device

safety analyzer instructions.

4. Connect the Cart power cord to the medical device safety

analyzer.

5. Perform test (500 V).

6. Ensure Insulation Resistance is greater than or equal to 1

Mohms.

7. Remove medical device safety analyzer connections to Cart

and return Cart to service.

Recommended Periodic Inspection and Maintenance

• Inspect Cord Thoroughly Before Each Use. DO NOT USE IF DAMAGED.

• Do Not Plug More Than SPECIFIED NUMBER OF WATTS Into Power System.

• Do Not Run Cord Through Doorways, Holes in Ceilings, Walls or Floors.

• FULLY INSERT Plug Into Outlet.

• Do Not Remove, Bend or Modify Any Metal Prongs or Pins of Cord.

• Do Not Use Excessive Force to Make Connections.

• Keep Away From Water. DO NOT USE WHEN WET.

• Keep Children Away From Cord.

• Do Not Plug Cord into An Extension Cord.

• AVOID OVERHEATING. Uncoil Cord and Do Not Cover It With Any Material.

• Do Not Drive, Drag or Place Objects Over Cord. Do Not Walk On Cord.

• GRASP PLUG to REMOVE FROM Outlet. Do Not Unplug By Pulling On Cord.

Polarized Connector Inspect for damage. Weekly Any user.

Power Outlets Inspect for damage or dirt. Weekly Any user.

Circuit Breakers Test Circuit Breakers. Weekly IT Personnel

Coiled Cord

Inspect for wear, damage, or

stretching. Move attachment

hook to avoid dragging on  oor

Weekly Any user

Power Strip Internal & External Components Disposal

1. Internal wiring, power cord and all electrical components should be recycled through an electronics recycler.

2. Remaining plastics and metals can be recycled through a commercial recycler.

Recommended Periodic Inspection and Maintenance

Component Action How often By whom

UI, Ethernet,

USB cables

Inspect for wear,

pinching, bad connectors

Monthly Any user

Casters

Inspect for wear and

debris

Monthly Any user

Maximum

Load

Inspect to ensure that

maximum recommended

loads are not exceeded

Daily Any user

Power System

SLA batteries

Replace lead acid

batteries

1,2

It is recommended that a discharge

test be conducted when cart

is  rst purchased to determine

runtime with computer equipment

con gured on the cart. Change

batteries when instructed by

StyleLink battery management

software. If StyleLink is not used,

it is strongly recommended that

a monthly discharge test be

conducted to determine runtime

loss. If runtime is less than 50% of

original, batteries must be changed.

IT Personnel

Power Module

Inspect for dust at intake,

vacuum as required using

a vacuum cleaner that

DOES NOT generate ESD

(Electrostatic Discharge)

Monthly IT Personnel

Battery

harness

Inspect for wear,

cracking, pinching, or

other damage

Monthly IT Personnel

Coiled Cord

Inspect for wear, damage,

or stretching.

Weekly Any user

1. Please dispose of all batteries in accordance with local law

2. Always replace with similar size battery (33 A-h to replace 33 A-h) and always replace in pairs

1 2 ... 21 22 23 24 25 26 27

Kommentare zu diesen Handbüchern

Keine Kommentare

Ergotron StyleView Betriebsanweisung Seite 26

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Multimedia-Wagen & Ständer Ergotron StyleView